![]() ![]()
Step 6: Restart your computer and Windows will automatically install AHCI drivers. Step 2: Type the bcdedit /set safeboot command and hit the Enter key. Step 1: Type Command Prompt in the Cortana’s search box and run Command Prompt as administrator. Enable AHCI After Win 10 Installation via CMD On boot, Windows 1ill automatically install AHCI drivers. Step 4: Enable AHCI in BIOS or UEFI firmware settings, save and exit this change, and restart your computer. CHANGE AHCI TO RAID WINDOWS 10 REGISTRY PCStep 3: Boot your PC to BIOS or UEFI firmware settings. ![]() FYI: I've done this on 2 Seagate 320GB hard drives and used the RAID as RAID 0 and as the C drive. CHANGE AHCI TO RAID WINDOWS 10 REGISTRY MANUALCheck your mobo manual on the exact steps of setting up the RAID. ![]() This leaves you C drive intact and separate. Type 0 in the Value data field and click the OK button.Įxpand storahci and double-click the Start DWORD and set its value as 0.Įxpand StartOverride and double-click the 0 DWORD to modify its value to 0. Then go into the BOIS and setup the RAID for those 2 drives. Then change the value of the DWORD to 0 and click the OK button to confirm.Įxpand StartOverride and then double-click the 0 DWORD. In the right pane, double-click the Start DWORD to modify it. ![]() HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\ Step 2: Navigate to the following path to find the folders below mand modify them one by one. Once getting the window, please type regedit in the search zone and then hit the OK button to open Registry Editor. Step 1: Press Windows R to call out the Run window. Enable AHCI After Win 10 Installation via Registry Editor Note: Before carrying out the following steps, it is highly suggested you create a system restore point in case that something goes wrong. So, you can effectively use your hard disk under multitasks after enabling AHCI. The reason why the disk performance can be improved by enabling the AHCI mode is that using this mode can greatly minimize the travel of data seek (the read/write speed of a SATA hard drive can be increased by about 30%). While AHCI supports some important new features that IDE dies not, like hot-plugging hard drives, Furthermore, AHCI offers an improved performance over IDE. But it lacks support for new technologies. Under one of the modes, a hard drive communicates with the computer system adopting a SATA storage controller.īasically, IDE is for average computer uses and is the most compatible with other technology, especially older devices. In other words, the performance of the hard disk will be greatly reduced if not using this mode.ĪHCI and IDE are two modes. Change it’s value to 0 and then click OK. Select iaStorV then from the right window pane double-click on Start. The top benefit of enabling AHCI mode for hard disk is that the disk can run at a higher speed than the disk adopting IDE mode. Press Windows Key R then type regedit and hit Enter to open Registry Editor. Short for Advanced Host Controller Interface, AHCI is an Intel technical standard that specifies the operation of SATA host bus adapters. But it is necessary to learn about this term due to the quick development of hard disk. Enable AHCI After Win 10 Installation via CMDįor many general users, AHCI is a strange term.Enable AHCI After Win 10 Installation via Registry Editor. CHANGE AHCI TO RAID WINDOWS 10 REGISTRY HOW TOIn this post, MiniTool shows you the reasons and how to enable AHCI after Win 10 installation. A quick little post, more to come.You may wonder about the reasons for enabling Advanced Host Controller Interface (AHCI) in Windows 10. When Windows starts, it will detect the change, load new disk drivers, and do one more reboot to start up with them. Save the new BIOS configuration and restart so that Windows boots.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |